2.5 Quiz Cevaplari

The commands shown in the graphic were entered to alter the startup sequence
of the router. On the next reload, which IOS will be loaded?
The router will load c2500-js-l.112-26d.
The router will load c2500-d-l.120-9.
The router will load the IOS from ROM.
*** The router will boot into ROM monitor mode.*
2 Where does a router look for boot system statements?
*** NVRAM *
3 Which of the following are steps in saving a router configuration file to
a TFTP server? (Choose three.)
Enter configuration mode.
*** Enter the IP address to the TFTP server. *
*** Use the copy running-config tftp command. *
Use the copy tftp running-config command.
*** Name the configuration file or accept the default name. *
4 Routers have different types of memory. Choose the answer that describes
flash memory.
provides working storage
*** stores a fully functional IOS image *
stores the startup configuration file
initializes the code used to boot the router
5 Which command is used to change the order in which the router looks for
system bootstrap information?
*** config-register *
config system bootstrap
6 Which of the following can be configured as a source for the IOS image by
using the boot system command? (Choose two.)
*** TFTP server *
HTTP server
Telnet server
*** Flash memory *
NVRAM memory
7 Which two items below are required by routers in order for them to perform
their basic operations? (Choose two.)
a tftp server
*** a configuration file *
a configuration register file
*** an operating system file *
a DNS table
8 The router has been configured with a valid configuration file. Which of
the following could be a cause for a router not booting normally? (Choose
*** The flash image is corrupt. *
A console cable is disconnected.
The flash image is located in NVRAM.
The startup configuration file is incomplete.
*** The router encountered a hardware error. *
9 The Cisco IOS image naming convention allows identification of different
versions and capabilities of the IOS. What information can be gained from
the filename c2600-d-mz.121-4? (Choose two.)
The "mz" in the filename represents the special capabilities and features of
the IOS.
The file is uncompressed and requires 2.6 MB of RAM to run.
*** The software is version 12.1, 4th revision. *
The file is downloadable and 121.4MB in size.
*** The IOS is for the Cisco 2600 series hardware platform. *
10 Which part of the configuration register indicates the location of the
the bootstrap
*** the boot field *
the IOS locator
the system image loader
11 If a router cannot find a valid configuration file during the startup
sequence, what will occur?
The startup sequence will reset.
*** The router will prompt the user for a response to enter setup mode. *
The startup sequence will halt until a valid configuration file is acquired.
The router will generate a default configuration file based on the last
valid configuration.
The router will monitor local traffic to determine routing protocol
configuration requirements.
12 What command can be used in ROM monitor mode to run the IOS image in
rommon1> config-register 0x2102
*** rommon1> boot flash:filename *
rommon1> xmodem:filename
rommon1> boot system flash:filename
rommon1> reload system flash:
13 What does a configuration register setting of 0x2102 indicate on a
It tells the router to locate and load the IOS from NVRAM.
It tells the router to locate and load the IOS from FLASH.
*** It tells the router to bypass the configuration in NVRAM. *
It tells the router to look in the startup configuration for boot system
14 Routers have different types of memory. Choose the answer that describes
provides working storage
stores a fully functional IOS image
*** stores the startup configuration file *
initializes the code that is used to boot the router
15 Which command will move configuration files among RAM, NVRAM and a TFTP
*** copy *
16 Which command will copy an IOS image from a TFTP server to a router?
*** Router# copy tftp flash *
Router# copy flash tftp
Router(config)# copy tftp flash
Router(config)# copy flash tftp
17 If the configuration register instructs a router to look for
configuration information in NVRAM and no boot system commands exist there,
from where will the router next attempt to boot the IOS?
*** FLASH *
18 An IOS image can be copied into flash from a TFTP server. Which of the
following statements are true regarding this process? (Choose three.)
*** A series of "!’s" are displayed as the image is downloaded successfully to
flash. *
The copy tftp flash:filename ip address command is used to copy the IOS from
the server to flash.
*** After the new flash image is downloaded, it is verified. *
*** A series of "e’s" are displayed as the current IOS image is erased from
flash. *
Flash must be cleared with the erase command prior to beginning the download
19 If boot system commands have been configured, which of the following
could happen if a router fails to obtain an IOS image from the primary
sources during bootup?
*** The router will load a subset of a full IOS version from system ROM. *
The router will attempt to reboot two times before failing.
The router will load the last good IOS image from NVRAM.
The administrator will be prompted to load a valid IOS image.

Kaynak: Cisco Curr v3.1

Belgeci , 2280 belge yazmış

Cevap Gönderin